A walk-in cooler climbing above 41 degrees, a reach-in that ices up every night, a prep cooler failing a health inspection, or a condensing unit short-cycling on a hot afternoon. TakiDA services commercial refrigeration for restaurants, breweries, wineries, event venues, gyms and convenience stores across Dripping Springs and the surrounding Hill Country. EPA Section 608 Universal certified and insured. Commercial diagnostic $149, applied toward the repair.
Call (737) 388-3867 | Request a visit

Common causes. A low charge from a slow leak, a restriction in the liquid line, a dirty condenser, a failing compressor, or a defrost system that never terminates so the coil stays iced.
What we do. We take suction and discharge pressures with superheat and subcooling, read the box and coil temperatures, and inspect the condenser. The separating test on a sealed system is to stop the compressor and watch the low side: pressure that climbs toward ambient says restriction, and a pull into vacuum says the charge is gone. We find the leak before we add refrigerant, because topping off an open system is money burned and a reportable practice.
Common causes. A failed defrost timer, heater or termination thermostat, a low charge, a blocked air path from overstacked product, or a door gasket letting humid air in all day.
What we do. We verify the defrost cycle actually runs and terminates, measure heater current, check the gaskets, and confirm the fans move air across the whole coil. A box that ices nightly usually has a defrost fault, not a refrigerant problem, and that distinction decides the whole repair.
Common causes. A high-pressure cutout tripping on a dirty or sun-baked condenser, a failed start component, low voltage at the disconnect, or a condenser fan motor that has quit.
What we do. We measure voltage under load and compressor amps against the nameplate with the clamp meter, check the fan and the cutout, and clean the condenser. Rooftop and outdoor units in Hill Country summer heat are the usual victims, and airflow fixes more of these than parts do.
Common causes. A blocked or frozen condensate drain line, a cracked drain pan, a failed drain line heater, or a coil icing and then dumping when it thaws.
What we do. We clear and pitch the drain line, test the heater, and find out why the coil iced in the first place. Standing water in a kitchen is a slip hazard and an inspection finding, so this one gets fixed at the cause.
Common causes. An evaporator fan out, pans blocking the air channel, a rail gasket missing, or a low charge showing itself at the warmest part of the box first.
What we do. We measure temperature at the product line rather than at the dial, check the fan and the rail seals, and verify the charge. Prep tables are the single most common unit to fail an inspection, and the fix is often airflow rather than refrigerant.
Common causes. A failed start capacitor or relay, worn mounts, liquid floodback from a defrost fault, or an internal winding failure.
What we do. We test the starting components and read the winding resistance before condemning anything. A compressor is the most expensive part in the system, and we do not name it as the fault until the measurements say so. If it is the compressor, we tell you plainly what that costs against a new condensing unit.
Common causes. Torn gaskets, a sagging walk-in door, a failed door heater on a freezer, or a closer that no longer pulls the door home.
What we do. We replace gaskets, adjust hinges and closers, and test the frame heater. Gaskets are cheap and they are the highest-return repair on a walk-in, because every hour of leaking door is runtime you pay for.
Common causes. A failed probe, a probe hanging in the wrong place, a controller set up wrong after a previous service call, or a loose sensor connection.
What we do. We verify each probe against a measured temperature, reposition probes that were left dangling, and set the controller to the manufacturer's values. A box that reads fine on the display and fails a thermometer is a probe problem, and we check it that way around.
Walk-in coolers and freezers, reach-in refrigerators and freezers, under-counter and back-bar coolers, prep and sandwich tables, display and merchandiser cases, keg coolers and draft systems, blast chillers, and remote and self-contained condensing units. We service Traulsen, True, Turbo Air, Hoshizaki, Continental, Beverage-Air, Norlake, Kolpak, Heatcraft, Copeland and Scotsman equipment for restaurants, taprooms, wineries, event venues, spas, gyms and convenience stores.
The commercial diagnostic is $149 and it is credited toward the repair when you approve it. Gaskets, fan motors, defrost components, probes and drain repairs are the moderate end. Leak repair with evacuation and recharge, compressor replacement and condensing unit changes are the expensive end, and we will give you the repair number against the replacement number so the decision is yours and not a surprise. You get a written estimate with parts, labor and tax before any work starts, and it stays good for 30 days. Labor carries a 3 month warranty and installed parts carry one year against manufacturer defects. All sealed-system work is performed under EPA Section 608 certification.
We cover Dripping Springs and the businesses around it, from the restaurants and taprooms along Mercer Street to the wineries, distilleries and event venues out along Ranch Road 12 and Highway 290 West, plus the retail along the 290 corridor. Nearby Driftwood, Henly and Wimberley are inside our normal route, and Bee Cave, Lakeway and Austin are a short run from here.
Commercial calls take priority and same-day is usually possible. Tell us the box temperature and whether product is at risk when you call, and we will tell you honestly whether you should start moving inventory before we arrive.
A system that is low is leaking, and adding gas without finding the leak is both a short-term patch and a practice we will not sign off on. We will stabilize you for service where we safely can, then come back and repair the leak properly.
Tell us your service window when you call. A box going warm does not wait for morning, and we would rather plan around your rush than work through it.
Sometimes, and sometimes it is how it is loaded. We measure at the product line, check airflow and the rail seals, and tell you which it is. That answer is usually cheaper than a new table.
Tell us the equipment, the brand, the current box temperature and how fast it is drifting, and we will come prepared for the sealed system as well as the simple causes.