An ice machine that stopped producing, a harvest cycle that never releases, thin or cloudy cubes, or a bin that runs dry every afternoon service. TakiDA repairs and deep-cleans commercial ice machines for restaurants, taprooms, wineries, event venues, gyms and convenience stores across Dripping Springs and the surrounding Hill Country, where hard well water is the main reason these machines fail. EPA Section 608 Universal certified and insured. Commercial diagnostic $149, applied toward the repair.

Common causes. A bin thermostat or ice-level sensor that thinks the bin is full, a closed or clogged water supply, a failed water inlet valve, a scaled evaporator, or a sealed-system fault.
What we do. We read the machine's diagnostic lights and run it through a manual cycle, confirm water actually enters the trough, and check the bin sensor before touching refrigeration. On a sealed-system suspicion we take pressures and use the compressor-off test on the low side: pressure climbing says restriction, a pull into vacuum says the charge is gone. Scale and water supply account for most no-ice calls out here.
Common causes. Scale on the evaporator from hard water, a water distribution tube with blocked holes, a low water level in the trough, a failed water pump, or a thickness sensor out of adjustment.
What we do. We deep-clean and descale the evaporator, distributor and trough, clear the pump, and set the cube thickness to spec. In Dripping Springs this is the single most common service, and a machine on untreated well water needs it on a schedule rather than when it fails.
Common causes. A failed hot gas valve, a stuck harvest assist, scale bonding the slab to the evaporator plate, or a curtain switch that never tells the control the slab fell.
What we do. We watch a full harvest, test the hot gas valve for actual flow, and check the curtain switch. A machine that freezes a slab and then stalls will trip into a safety lockout, and clearing the code without fixing the harvest just repeats it tomorrow.
Common causes. A blocked bin or evaporator drain, a cracked trough, a failed inlet valve that will not shut off, a loose supply fitting, or condensate from a bin with a bad gasket in a humid kitchen.
What we do. We find the leak while it is running, clear and pitch the drains, and replace the valve, fitting or gasket at fault. Water under an ice machine in a kitchen is both a slip hazard and an inspection finding.
Common causes. A dirty air-cooled condenser, a machine installed with no clearance in a hot kitchen corner, high incoming water temperature, a low charge, or a failing compressor.
What we do. We measure air temperature at the condenser intake and the incoming water temperature, clean the condenser, and then take refrigeration readings. Published production figures assume cool air and cool water, and a machine in a 95 degree corner will never meet them no matter what gets replaced.
Common causes. Biofilm or slime in the trough and distribution tube, an exhausted water filter, scale in the water path, or airborne kitchen odors drawn through an open bin.
What we do. We perform a full sanitizing clean of every wetted surface, replace the filter, and check the bin lid and gasket. Slime in an ice machine is a food safety issue, not a taste complaint, and it gets treated that way.
Common causes. High discharge pressure from a blocked condenser, a long freeze or long harvest fault, a water-level sensor fault, or a thermistor out of range.
What we do. We read the stored code, then test the circuit the code names rather than clearing it and hoping. Safety lockouts are the machine telling you what already went wrong, and we treat the code as a starting point, not a diagnosis.
Common causes. A machine undersized for your volume, reduced production from scale or a dirty condenser, a bin sensor cutting off early, or ice melting faster than it is made in a hot room.
What we do. We measure the actual production rate against the nameplate and tell you whether you have a service problem or a capacity problem. If the machine is simply too small for your covers, we will say so rather than selling repeat repairs.
Modular cubers on bins, under-counter and self-contained units, nugget and flake machines, remote and air-cooled condensers, and water-cooled units. We service Hoshizaki, Manitowoc, Scotsman, Ice-O-Matic, Follett, True and Turbo Air for restaurants, bars and taprooms, wineries, event venues, spas, gyms and convenience stores.
The commercial diagnostic is $149 and it is credited toward the repair when you approve it. A full deep-clean and descale is the low end and is what most machines out here actually need. Water pumps, inlet valves, hot gas valves, thermistors and curtain switches are moderate parts. Compressor replacement and sealed-system leak repair are the expensive end, and on an older machine we will give you the repair number against a replacement so the choice is yours. You get a written estimate with parts, labor and tax before any work starts, and it stays good for 30 days. Labor carries a 3 month warranty and installed parts carry one year against manufacturer defects. All sealed-system work is performed under EPA Section 608 certification.
We cover Dripping Springs and the businesses around it, from the restaurants and taprooms along Mercer Street to the wineries, distilleries and event venues out along Ranch Road 12 and Highway 290 West, plus the retail along the 290 corridor. Nearby Driftwood, Henly and Wimberley are inside our normal route, and Bee Cave, Lakeway and Austin are a short run from here.
More often than the manual says. Manufacturers generally call for twice a year, and on untreated hard water in this area a machine often needs it quarterly. We will tell you what your machine's scale looks like and set a realistic interval.
It helps a great deal, and a scale-inhibiting filter extends the life of the evaporator and the water pump. It is not a substitute for cleaning, but it does make the cleaning interval longer and the machine last longer.
A proper deep clean takes a few hours with the machine off. Tell us your service window and we will schedule around it rather than through it.
Commercial calls take priority and same-day is usually possible. A bar with no ice is treated as urgent.
Tell us the brand, the model, whether the water is treated, and what the machine is doing, and we will arrive ready to clean, repair or diagnose the sealed system on the first visit.