An ice maker is the first appliance in a Dripping Springs house to tell you what the water is really like. Well water here carries minerals, iron and fine sediment, and all of it ends up in the fill valve, the fill tube and the mold. Production drops a little every month until somebody notices the bin is empty. We repair refrigerator ice makers and standalone undercounter units across Belterra, Caliterra, Headwaters, Highpointe, Rim Rock and the acreage out Hamilton Pool Road. Diagnostic is 99 dollars and goes toward the repair.

Common causes. A shut or partly shut saddle valve, an inlet valve screen packed with sediment, a filter nobody has changed, or a frozen fill tube. On refrigerator units a failed module or a shut-off arm stuck in park stops production completely.
What we do. We check supply pressure at the valve first, then fill volume, then the module. A new ice maker on a starved or sediment-fed line makes exactly as much ice as the old one did.
Common causes. Mineral scale on the mold and in the fill path slows the fill, so harvest happens before the cube is full. On well water this builds far faster than on treated city water, and iron leaves the cubes looking dull or faintly stained.
What we do. We time the fill and measure how much water actually reaches the mold, then look at what the house treatment is doing. We will tell you plainly when the problem is the water rather than the appliance.
Common causes. Sulfur or iron coming through untreated, an exhausted carbon filter, or old ice sitting in the bin absorbing everything around it. A softener that regenerates poorly can also push salty-tasting water through.
What we do. We check the filter and the supply, clean the bin and mold, and tell you whether treatment or a dedicated filter on the ice line would fix it. We do not sell appliance parts for a water problem.
Common causes. A weeping inlet valve letting water through when it should not, fill volume set too high, or a failed thermostat or harvest heater.
What we do. We test the inlet valve for seepage with power off, measure fill volume and test the harvest circuit. Chipping ice out without finding the cause buys about a week.
Common causes. A split or crushed supply line, a cracked filter housing, a leaking inlet valve, or on standalone units a blocked drain. Sediment is hard on valve seats, so weeping valves are more common here than in town.
What we do. We trace the line from the shutoff, pressure check it, repair or clear the drain, and look at what the water has reached under the cabinet.
Common causes. Ice that is not used refreezes together. It becomes a repair when the real cause is a slow leak into the bin, a door seal letting warm air in, or a defrost problem raising freezer temperature.
What we do. We check the seal, the freezer temperature and the fill for seepage before replacing anything.
Common causes. Covered patios and outdoor kitchens are common on these lots, and an indoor-rated machine will not hold its plate output at 100 degrees. Add a condenser loaded with caliche dust from the drive and production collapses.
What we do. We service the condenser, check clearance around the cabinet and measure real output against the rating. If the unit was never outdoor-rated we say so.
Common causes. A cube jammed behind the ejector, a worn gear in the module, a failed motor, or on standalone units a cutter grid or auger problem.
What we do. We find what is binding before ordering parts, because a jam and a dead module are different repairs.
Refrigerator ice makers in side-by-side, French door and bottom freezer units, standalone undercounter machines indoors and in outdoor kitchens, and nugget and gourmet cube units. Common brands here include Whirlpool, KitchenAid, Maytag, GE, Frigidaire, LG, Samsung, Scotsman, U-Line and Sub-Zero.
Commercial ice machines at wedding venues, breweries and tasting rooms are a different service and are covered on our commercial ice machine page.
Diagnostic is 99 dollars for a residential unit, credited toward the repair when you approve the work. The final price depends on the part, whether the water line and valve need work, and whether the unit is built in.
Work carries a 3 month labor warranty and installed parts carry a 1 year manufacturer defect warranty. We quote before starting.
Belterra and the Heights at Belterra, Caliterra, Headwaters, Highpointe, Ledgestone, Rim Rock, Sawyer Ranch, and the acreage properties out Hamilton Pool Road and toward Henly. We also cover Driftwood and Wimberley, and run back toward Bee Cave and Austin along 290.
Shorter filter life and faster scale buildup than the manual assumes. With treatment and a filter on the ice line an ice maker lasts a normal life here. Without it, expect declining output within a year or two.
It can dull or tint it and affect the taste, and it accelerates deposits in the valve and mold. That is a water treatment question first and an appliance question second.
Yes, both. Outdoor units here fail mostly from heat, dust and airflow rather than from the ice maker itself.
Same-day or next-day in most cases. We come stocked for the common failures so the repair finishes on the first visit where possible.
Call or book online and tell us what the ice maker is doing and whether the house is on a well. EPA certified and insured.
We repair all major residential appliance brands across Central Texas, including Whirlpool, GE, Samsung, LG, Maytag, Frigidaire, KitchenAid, Amana, Bosch, Electrolux, Hotpoint, Kenmore, Haier, Fisher & Paykel, Sub-Zero, Wolf, Viking, Thermador, JennAir, Dacor, U-Line, Marvel, Miele, and GE Monogram.