A dish machine that will not reach sanitizing temperature, one that leaves film on every glass, a door machine that will not drain, or a conveyor that stalls mid-rack during service. TakiDA services commercial dishwashers for restaurants, cafes, country clubs, bars and catering kitchens across West Lake Hills and the surrounding 78746 area. Insured and certified. Commercial diagnostic $149, applied toward the repair.
Call (737) 388-3867 | Request a visit

Common causes. A booster element buried in scale or failed outright, a thermostat out of calibration, incoming water arriving below what the machine needs, weak rinse flow from blocked nozzles, or a pressure regulator that has drifted.
What we do. We measure real rinse temperature at the manifold rather than trusting the gauge, test the booster element and its thermostat, and check incoming temperature and rinse pressure. A club or restaurant kitchen running long gaps between services often has the booster cooling right down between rushes, and a weak element shows up at the first rack rather than the fiftieth.
Common causes. Hard water scale, rinse aid not drawing or the container empty, a blocked rinse arm, wash water running cool, or detergent concentration off.
What we do. We descale and clear the arms and nozzles, confirm rinse aid and detergent are actually being drawn, and measure wash and rinse temperatures. Dining rooms around here put a lot of stemware through a machine every night, and cloudy glasses get noticed at the table before anything else in the kitchen does. The fix is almost always water treatment and dispenser draw rather than a new machine.
Common causes. A blocked scrap basket or sump, a drain valve solenoid that will not open, a failed drain pump, a drain line packed with grease, or a standpipe set at the wrong height.
What we do. We clear the sump and the line, test the valve or pump for both voltage and actual flow, and check the standpipe and air gap. Grease is usually the real story, and in an older building with a long horizontal run to the main it builds up faster than anyone expects.
Common causes. A clogged inlet screen, a dead fill solenoid, a float or level probe stuck, a supply valve left closed, or low incoming pressure.
What we do. We measure supply pressure at the machine, clean the inlet screen, test the solenoid and clear the level sensor. The screen solves this more often than any other single part, and it costs nothing to check first.
Common causes. Debris jammed in the impeller, a worn pump seal letting water into the motor, a failed bearing, or a motor pulling over its rating.
What we do. We clear the impeller, measure motor current against the nameplate and inspect the seal. A leaking seal will take the motor with it if it is left alone, so finding it early turns an expensive repair into a cheap one.
Common causes. A worn drive chain or pawl bar, a rack jammed in the tunnel, a failed drive motor or clutch, or a limit switch holding the cycle for a fault that has already cleared.
What we do. We inspect the drive and the limit switches and replace the worn linkage. A conveyor that runs fine empty and stalls with racks in it is nearly always mechanical, so we start there instead of chasing the control.
Common causes. A squeeze tube gone hard or split, an empty container nobody noticed, an air leak on the pickup line, or a dispenser pump that has quit.
What we do. We replace the tubing, check the pickup for air and test the pumps. This one matters more than it looks: a machine with dead dispensers runs, sounds and smells completely normal while failing the single job it exists to do, so we verify draw instead of assuming it.
Common causes. Worn door gaskets, a door out of alignment, a cracked tank weld on an older machine, a loose pump or fitting, or a missing curtain on a conveyor.
What we do. We replace gaskets and curtains, align the door and tighten or replace fittings. If the tank itself is cracked we say so straight out, because a welded repair on a thin old tank rarely holds and you should hear that before paying for one.
Under-counter dishwashers, door and hood-type machines, single and multi-tank conveyors, glass washers and bar washers, high-temp machines with booster heaters, and low-temp chemical sanitizing machines. We service Hobart, Jackson, CMA, Champion, Ecolab, Moyer Diebel and Insinger equipment for restaurants, cafes, country clubs, bars and catering kitchens.
The commercial diagnostic is $149 and it comes off the repair when you approve it. Descaling, gaskets, curtains, dispenser tubing, rinse arms, valves and thermostats are the moderate end and cover most of what these machines need. Booster heaters, wash pumps, drive assemblies and control boards are the expensive end. On an older machine we put the repair figure beside a replacement figure so you can weigh them yourself.
We cover West Lake Hills and the 78746 area around it, including the businesses along Bee Caves Road and the Loop 360 corridor, plus Westlake Highlands and Rollingwood. Lakeway and Bee Cave are inside our normal route, and Austin is a short run from here.
Not safely. It means the rinse is not reaching sanitizing temperature, and that is a health code problem, not a label problem. We measure the real rinse temperature and work out whether it is the booster, the thermostat, the incoming water or the rinse flow. Running it on the assumption the labels are faulty is the one thing not to do.
Nearly always hard water combined with rinse aid that is not drawing. Both are measurable and both are cheap to fix, and together they cost far less than the replacement glassware a dining room buys trying to solve it the other way.
Tell us your window and we will work to it. A dish machine down means hand washing through a full service, so getting in before doors open or after last cover is better for everyone.
Commercial calls go to the front of the schedule and same-day is usually possible. A machine failing sanitation is treated as urgent, because it is a health code exposure and not just an inconvenience.
Tell us the brand, whether it is high-temp or low-temp, and what it is doing, and we will arrive ready to descale, repair or diagnose on the first visit.