Commercial dish machines here live or die by water. Hard Hill Country water scales the tank, the booster heater and the rinse arms, and once scale is on the element the final rinse never reaches temperature. Bar glasswashers show it first, because cloudy glassware is visible to every guest. We service restaurants, bars, clubs, marinas and event kitchens across Lago Vista, Point Venture and Jonestown. Commercial diagnostic is 149 dollars and goes toward the repair. EPA certified and insured.

Common causes. Scaled or blocked wash arm jets, a clogged strainer, a worn wash pump, or a tank not filling to the right level. On hard water the jets close up gradually and nobody notices the day wash quality dropped.
What we do. We pull and inspect the arms and jets, check the strainer and pump output, and verify the fill level before anything else.
Common causes. A scaled booster heater element, a failed booster thermostat or contactor, incoming water colder than the booster expects, or low rinse pressure. On a high temperature machine this is a sanitation problem, not just a cleaning one.
What we do. We measure actual rinse temperature at the manifold rather than reading the gauge, then test the element and controls. Scale on the element is the usual finding here.
Common causes. This water, plus a deliming interval set from the manual rather than from reality. Scale costs you rinse temperature, wash pressure and element life all at once.
What we do. We delime the machine properly and tell you a realistic interval for your water and volume, and what filtration would change.
Common causes. A plugged fill valve screen, a float or level probe fouled with scale and grease, a drain valve stuck, a failed drain pump, or a drain line blocked downstream.
What we do. We clean the level sensing, test the fill valve and the drain, and confirm the house drain is actually accepting the discharge.
Common causes. Worn door gaskets or curtains, a cracked tank weld, a loose rinse manifold, or a drain connection that has worked loose. In a bar this shows up behind the glasswasher where nobody looks until the floor is wet.
What we do. We run the machine and find the real source, then repair the gasket, fitting or manifold rather than guessing.
Common causes. An empty container nobody checked, a failed dispenser pump, a cracked or kinked chemical line, or a squeeze tube worn out. Dispensers are often on a chemical supplier contract, and we will tell you when a fault belongs to them.
What we do. We verify the chemical actually reaches the tank and identify which part of the dispensing system failed.
Common causes. A door switch or interlock, a failed timer or control board, a thermostat open on the booster circuit, or a contactor that is not pulling in.
What we do. We test the interlock chain and the control circuit. Door switches on a machine cycled hundreds of times a day wear out and are a common and cheap fix.
Common causes. Hard water film, insufficient rinse temperature, no rinse aid, or etching that is already permanent. Film wipes off, etching does not, and the difference decides whether this is a repair or a replacement of glassware.
What we do. We check rinse temperature and chemical first and tell you honestly which of the two you are looking at.
Undercounter machines, door and hood type, conveyor and flight machines, bar glasswashers, high temperature with booster heaters and low temperature chemical sanitizing units. Common brands include Hobart, Jackson, CMA, Ecolab, Champion and Moyer Diebel.
Seasonal and club kitchens should note that a machine idle for months comes back with scale set hard and seals dried out. Before the first busy weekend is the cheap time to find that.
Commercial diagnostic is 149 dollars and is credited toward the repair when you approve the work. The final price depends on the part, how much deliming the machine needs, and whether plumbing or electrical work is involved.
Work carries a 3 month labor warranty and installed parts carry a 1 year manufacturer defect warranty. We quote before the work starts.
Lago Vista including the marina and club areas, Point Venture, Jonestown, and out along FM 1431 toward Leander and Cedar Park. We also cover Lakeway and Bee Cave on the south shore.
More often than the manual says. The right interval depends on your water treatment and your volume, and we will give you a number based on what the machine actually looks like inside.
Gauges are often the last thing to be right. We measure rinse temperature at the manifold, and a scaled booster element is the common finding.
It depends on your contract. Many dispensers belong to the chemical supplier, and we will tell you when a fault is theirs rather than charging you for it.
Same-day wherever we can. Tell us the brand and whether it is high temperature or chemical sanitizing when you call.
Call or book online and tell us the machine type and what it is doing. Commercial diagnostic 149 dollars, applied toward the repair.