A prep table is the hardest working refrigeration in an Austin kitchen and the easiest to misread. The base cabinet can be perfectly cold while the pans on the rail sit at fifty degrees, and the staff will tell you the unit is fine because the thermometer inside the door says so. On a line that runs hot, or in a trailer, that gap gets wide quickly.

This is the complaint that matters, because it is the one an inspector writes down. The rail is cooled by a curtain of cold air across the top of the wells, and anything that disturbs that curtain, overfilled pans, missing pan dividers, a lid left open, a fan that has slowed, will leave the product warm while the cabinet below reads perfectly. Product temperature is measured in the pan, not at the door thermometer.
When the base holds and the top does not, the problem is almost always airflow rather than refrigeration. A blocked return at the back of the well, a rail fan that has failed, or ice narrowing the air path will do it. Replacing refrigerant into a system that is working correctly will not help, which is why the split between base and rail gets established first.
Prep tables run with the lids open all service, pulling humid kitchen air straight across a cold coil. If defrost is not keeping up, or a gasket is letting in even more humidity, the coil ices and airflow collapses over the course of a shift. The unit then recovers overnight, which is exactly why the complaint only appears during service.
Most prep tables draw condenser air from the front or the side at floor level, right where fryers and ovens are dumping heat. Add grease and dust from the line and the condenser cannot shed heat at all. In an Austin kitchen in August this alone can account for the entire temperature problem, and it is the cheapest one on this page to fix.
Condensate is supposed to leave through a drain line into an evaporator pan or a floor drain. When that line blocks with debris, water backs up into the cabinet, soaks product boxes and eventually reaches the insulation. It is also an inspection finding, so it is worth clearing properly rather than mopping.
Prep table lids take abuse all day and the gaskets around the wells and the base doors harden, tear and pull loose. A door that does not seal runs the compressor constantly and still loses temperature, and on the rail a poor seal is a direct path for warm humid air onto the coil. Gaskets are inexpensive, and on a prep table they are consumables.
Continuous running is either a load problem or a system problem. A dirty condenser, a door or lid that does not close, warm product loaded during service, or an actual refrigerant or control fault. Pressures and the condenser get checked together, because the same symptom covers a very cheap repair and a very expensive one.
In a trailer, the prep table lives in the hottest, tightest spot available, often with the condenser facing a wall and a generator feeding it marginal voltage. Those units run at their limit all day. We look at power, airflow and condenser cleanliness before touching the sealed system, because that is where the answer usually is.
Sandwich and salad prep tables, pizza prep tables with raised rails, mega top and high capacity units, under counter refrigerated bases, and prep refrigeration in trailers and mobile kitchens. Common brands include True, Turbo Air, Beverage Air, Continental, Delfield, Traulsen, Randell and Atosa.
We are EPA Section 608 Universal certified and insured, with certificates of insurance available when a building requires one.
The commercial diagnostic is one hundred and forty nine dollars and it is credited toward the repair once you approve the work. Fans, gaskets, lids, controls, drain line clearing and a proper condenser cleaning are all routine. Sealed system work or a compressor on a prep table is a larger decision and we will compare it honestly against a replacement unit.
If you have an inspection coming or a product temperature issue right now, say so when you call so we can prioritize correctly.
Downtown and Rainey Street, East Sixth, East Austin, South Congress and South Lamar, Bouldin, Zilker, Burnet Road and the Domain, North Loop and Hyde Park, Riverside and Airport Boulevard, and the trailer parks and commissary kitchens around them.
Possibly not in the way you think. That split normally means the rail airflow is disturbed rather than the refrigeration being dead. Overfilled pans, missing dividers, lids left open and a failed rail fan all produce it, and the first three cost nothing to correct.
Fill to the line and not above it, keep the dividers in, and close the lid when the line is not actively working the well. The cold air curtain only works if there is somewhere for it to travel, and an overfilled pan blocks it completely.
On a prep table sitting on a hot line, every three months is realistic and monthly is better in a heavy kitchen. It is the single highest return maintenance item on this equipment and the one most often skipped until the unit fails in July.
Yes, regularly. Tell us whether you are on shore power or a generator when you call, because power quality is frequently the reason a trailer unit cannot hold temperature on site when it holds fine at the commissary.
Fans, controls, gaskets and drains are always worth repairing. A compressor on an older low cost prep table often is not, especially where the cabinet has already taken water damage. You get both numbers before you decide.
Tell us the make, what the base cabinet reads, and what the pans on the rail actually measure, and we can usually narrow it down before we arrive. Call (737) 388-3867 or book online. The one hundred and forty nine dollar commercial diagnostic is credited toward the repair.