The ovens in Bee Cave kitchens tend to be wall ovens in pairs or professional ranges, and both are built to hold a temperature closely. That is exactly why a fifteen degree drift gets noticed here: the equipment is accurate enough that the cook can tell when it stops being accurate.

Calibration drift. The oven sensor reads slightly high or low and the control heats to the wrong actual temperature. The test is a measurement in the cavity against the setpoint, not a judgment about the food. Most ovens can be offset in the control once the real number is known, and that is often the whole repair.
On electric, a bake or broil element, a relay on the control board, or one leg of the supply lost. On gas, the igniter, the safety valve or the ignition control. The igniter deserves its own note: it can glow brightly and still draw too little current to open the valve, so it gets measured rather than judged by whether it looks hot.
That isolates the fault to the dead cavity: its element, its relay or its sensor. The shared control board is possible but it is the less likely answer when one cavity is behaving perfectly. On built-in pairs this matters because pulling the unit out of the cabinet is most of the labor.
Door seal and hinges first. A heavy professional range door that has dropped on its hinges no longer seals along the bottom, and the oven loses heat continuously. It is a cheap repair with a large effect, and it is routinely mistaken for a failing element.
Self-clean runs the cavity far hotter than baking and it is hard on thermal fuses, door locks and control boards. An oven that worked before the cycle and not after usually lost one of those three. On high-end units we will often suggest cleaning by hand instead and explain why.
Clean natural gas burns blue with a defined cone. Yellow means the air and gas mixture is wrong: a partly blocked port, a shifted burner cap, or a range set up for the wrong fuel. On a range converted between natural gas and propane, the orifices are the first thing to verify.
Scale in the generator and on the probes. Hill Country water is hard, and a steam oven boils it continuously. Descaling on the schedule in the manual is what keeps these alive; a unit that has never been descaled will keep reporting faults no matter which part is replaced.
On wall ovens the control sits above the cavity and takes years of heat. Membrane keypads fail trace by trace and displays dim before they quit. Before a board is ordered we check whether a sensor is reporting out of range, because that mimics a control fault closely.
Single and double wall ovens, professional and dual-fuel ranges, gas, electric and induction ranges, steam and combination-steam ovens, speed and convection microwaves, warming drawers and second ovens. Common brands include Wolf, Sub-Zero, Thermador, Monogram, Viking, Miele, Bosch, JennAir, KitchenAid, Whirlpool, GE and Frigidaire.
Gas work is done to manufacturer specification, and a range converted between natural gas and propane gets verified rather than assumed.
The diagnostic is ninety nine dollars for a residential call and it is credited toward the repair once you approve the work. Elements, igniters, sensors, thermostats, door seals, hinges and relays are routine parts. On professional and European equipment some parts are brand-specific and ordered, and we will give you the lead time before you commit rather than after.
Replacing a built-in wall oven means matching the cutout and the trim, so repairs are often clearly worth doing on units where a freestanding equivalent would be replaced.
Spanish Oaks, Falconhead, Lake Pointe, Uplands, Homestead, Ladera, Bella Colinas, Sweetwater, Rough Hollow nearby, and the homes along Bee Cave Road and Highway 71.
Fifteen degrees changes baking noticeably; twenty five changes it badly. Most controls allow a calibration offset, and setting it correctly is a short visit rather than a parts job.
Sparingly, and not the night before you need the oven. The cycle is the single most common cause of a sudden oven failure. On high-end units manual cleaning with the manufacturer recommended products is gentler and avoids the risk entirely.
Yes. Give us the model and serial when booking so parts availability and lead time can be checked before the visit.
Scale, almost always, on hard water. Descaling on schedule and using the water treatment the manufacturer specifies solves most of it. Ignoring it eventually costs a steam generator.
Yes. Hinges and seals are inexpensive and a door that does not seal changes every bake, lengthens preheat and makes the oven look like it has a heating fault when it does not.
Tell us the brand and model, whether it is gas or electric, and what the oven is actually reading against the setpoint, and we can usually narrow it down and check parts before we arrive. Call (737) 388-3867 or book online. The ninety nine dollar diagnostic is credited toward the repair.
We repair all major residential appliance brands across Central Texas, including Whirlpool, GE, Samsung, LG, Maytag, Frigidaire, KitchenAid, Amana, Bosch, Electrolux, Hotpoint, Kenmore, Haier, Fisher & Paykel, Sub-Zero, Wolf, Viking, Thermador, JennAir, Dacor, U-Line, Marvel, Miele, and GE Monogram.