A microwave that runs but leaves the food cold, or one that is simply dead. We repair over-the-range, built-in and countertop microwaves across Leander — Crystal Falls, Travisso, Bryson and the older streets around Old Town — usually same-day or next-day. The $99 diagnostic goes toward the repair, and you get a firm price before any part is replaced.

The diagnosis below follows the manufacturers’ own microwave service manuals for Whirlpool, Maytag, GE, Samsung, LG and Frigidaire — their interlock checkout procedures, component tests and safety sequences — rather than general advice. A microwave is the one kitchen appliance where the inside is genuinely dangerous: the high-voltage capacitor holds a lethal charge after the power is off, and the service manuals open with that warning before anything else.
Common causes. The turntable turns, the light is on, the fan runs — and the food is cold. That means the control and the low-voltage side are fine and the high-voltage side is not: the transformer, the capacitor, the diode or the magnetron. The factory sequence checks them in that order, measuring the supply at the transformer primary first and condemning the magnetron last, because it is the most expensive part and the least often at fault.
What we do. We discharge the capacitor properly before anything is touched, then follow the manufacturer’s sequence with a meter. On an over-the-range unit we also price the repair against a replacement before recommending it, because a magnetron and transformer together can approach the cost of a new microwave.
Common causes. No display, no light, nothing. On a microwave that almost always means the line fuse has blown, and the fuse almost never blows on its own. The service manuals are explicit: a blown fuse in the monitor switch circuit means you check the door latch switches and the monitor switch before fitting a new fuse. If the latch switch sticks closed while the door opens, the monitor switch deliberately shorts the line and blows the fuse — that is the safety system working, not a random failure.
What we do. We test all three door switches before replacing any fuse, and the manufacturers tell us to replace the set together rather than one at a time, because a mismatched set is what caused the fault. Fitting a fuse without checking the switches blows the new fuse and leaves the real problem in place.
Common causes. Arcing is usually the waveguide cover burned through, a chipped cavity wall where the paint has gone and the steel is bare, metal trim on dishes, or food residue carbonised onto a surface. A damaged waveguide cover arcs reliably and gets worse quickly.
What we do. We stop the unit being used until it is inspected, because continued arcing damages the magnetron and the cavity. Then we check the waveguide cover and the cavity surfaces. A burned cover is an inexpensive part; a burned-through cavity wall usually is not worth repairing.
Common causes. Either the drive motor has failed, the coupler under the tray is broken or worn, or the roller ring is jammed with debris. On some models the control disables the turntable in certain modes, which is worth confirming before anything is opened.
What we do. We check the coupler and roller first because they are cheap and common, then test the motor. This is one of the few microwave faults that is reliably worth repairing on any unit.
Common causes. The door assembly carries the hooks that operate all three safety switches, so a cracked latch hook or a worn hinge stops the oven working entirely — by design. Doors take abuse on over-the-range units, where they are opened one-handed with a full plate in the other.
What we do. We check the door alignment and latch hooks and the switch adjustment together, since a door out of alignment stresses the switches and eventually blows the fuse. A microwave with a damaged door is not safe to use until it is fixed, and we say that plainly.
Common causes. On an over-the-range microwave the hood is part of the appliance, so the fan, its speed switch, the control board or the damper can fail independently of the cooking function. Grease-loaded filters and a damper flap stuck shut produce noise with no airflow, exactly as on a separate hood.
What we do. We check the filters, the damper and the duct path, then the motor and its switch. Many of these units are ducted into the cabinet rather than outside, which the homeowner often does not know, and we will tell you if that is what we find.
Common causes. An unresponsive panel is the membrane keypad or the control board. Over-the-range units cook their own electronics over the years with heat and grease rising from the range below, and the keypad is usually first to go.
What we do. We separate keypad from board by testing the panel, because they are very different prices. A keypad is often worth replacing; a control board on an older unit usually is not.
Common causes. Countertop microwaves are rarely worth a paid repair beyond a door switch or a turntable part. Over-the-range and built-in units are a different calculation: they are expensive to replace and often fitted into cabinetry, so a magnetron, a door assembly or a fan motor can be well worth doing.
What we do. We tell you which category your unit is in before any work is authorised, and we will not sell a repair on a countertop unit when a new one costs less than the part.
We work on over-the-range microwaves with built-in hoods, built-in wall and drawer microwaves, convection and speed-cook combination units, and countertop models where the repair makes economic sense.
Brands we repair in Leander: Whirlpool, Maytag, GE, GE Profile, Samsung, LG, Frigidaire, KitchenAid, Amana, Bosch, Electrolux, Kenmore, Sharp, Panasonic, Thermador and JennAir.
Diagnostics are $99 for a residential call, and that amount is credited toward the repair when you approve it. After the diagnosis you get a written estimate covering parts and labor, and nothing is replaced before you approve it. The final figure depends on which part failed — a door switch set, a fuse, a turntable motor, a keypad, a fan motor, or the high-voltage components — and whether the unit is an over-the-range installation that has to come down off the wall.
Completed repairs carry a 3-month labor warranty from TakiDA LLC and a 1-year parts warranty against manufacturer defects.
We cover Leander as a whole, including Crystal Falls, Travisso, Bryson and Old Town, and we reach most addresses in the city within about twenty minutes. Over-the-range units are standard across the newer subdivisions, and they take more abuse than a countertop unit ever does. Nearby Cedar Park, Georgetown, Liberty Hill and Round Rock are also in our service area.
No. The high-voltage capacitor holds a charge that can kill after the oven is unplugged, which is why every manufacturer service manual opens with that warning. Door switches and fuses look like simple parts, and the circuit they sit in is not.
That is the expected outcome. The fuse blows because a door switch has failed and the monitor switch shorted the line on purpose. Until the switch set is replaced, every new fuse does the same thing.
Yes, and those are the ones most worth repairing. Countertop units are usually cheaper to replace than to fix, and we will tell you that rather than selling a part.
Leander is our home city, so same-day is usually possible if you call in the morning, and next-day otherwise.
Tell us the brand, whether it is over-the-range, built-in or countertop, and what it is doing — no heat, completely dead, sparking, or a fan that will not run. That is normally enough for us to arrive with the right parts on the van.
We repair all major residential appliance brands across Central Texas, including Whirlpool, GE, Samsung, LG, Maytag, Frigidaire, KitchenAid, Amana, Bosch, Electrolux, Hotpoint, Kenmore, Haier, Fisher & Paykel, Sub-Zero, Wolf, Viking, Thermador, JennAir, Dacor, U-Line, Marvel, Miele, and GE Monogram.