A washer out of service in an apartment laundry room or a laundromat costs money every hour it sits. We repair commercial washers and washer-extractors in Leander — no spin, out-of-balance faults, drain and fill problems, inverter faults and bearing noise. The $149 commercial diagnostic is credited toward the repair, and you get a firm price before anything is replaced.

On a washer-extractor the drive measures drum speed before every spin step and decides whether the load is safe to accelerate. If it sees an imbalance it limits speed in stages, and on a severe one it will hold the drum at a crawl and refuse to extract at all. So a no-spin is often the machine protecting itself rather than a failed part. The out-of-balance switch itself is a normally closed switch, and a surprising share of no-spin calls turn out to be a broken wire at that switch rather than the switch or the drive. We check continuity there before anyone talks about an inverter.
Most controls make up to three attempts to redistribute a load, and after three consecutive failures they end the program. The cause is usually in the laundry room rather than the machine. Overloading is the obvious one, but underloading causes just as many imbalances — a single heavy mat or two towels in a large cylinder will never redistribute. The other common cause is a machine that did not finish draining before the spin step, which reads to the control as weight that will not move. Manufacturers warn against ever bypassing or disconnecting the balance system, and we will not do it either; severe out-of-balance extraction damages bearings, frames and floors.
These are the same part failing in two directions. There is a factory test for it that costs nothing: start an unloaded cycle and let it fill. If water runs out during the prewash segment, the drain valve is not closing. If it fills and holds but will not empty, the valve is not opening, and the order of checking is the fuse that feeds the valve, then the valve coil, then the valve body and the drain line. On many extractors the drain valve is a normally open gravity type, which is why the machine dumps its water when power is lost — that is designed behaviour, not a fault.
Fill faults split cleanly between supply and machine. Supply means a closed or partly closed shutoff, a clogged inlet screen, or low pressure because something else in the building is running. Machine means the inlet valve, the water level sensing tube, or the control. The level tube is the one people miss: a tube partly blocked with lint and detergent residue reports the wrong level, so the machine either fills forever or thinks it is full with four inches of water in the drum. Clearing the tube is a ten-minute job and we check it before any valve is quoted.
An inverter communication error means the control board and the drive are not talking, and the first thing to check is the communication cable and its plug, not the drive. Plugs that look fully seated often are not, and on machines that live next to an extracting cylinder, vibration works them loose over years. A real drive failure is a real cost, so it is worth being certain. Overcurrent and overvoltage faults from the drive are different and usually point at the motor, the load, or the supply rather than at the drive itself.
Door gasket, drain line, or hose connection, and they leave different evidence. A door seal leaks only while the drum is turning and leaves water in an arc in front of the machine. A drain line or valve leak shows up at the moment of drain and runs from under the back. A supply hose weep is constant and usually dries a mineral trail. On vended machines we also check that the drain trough itself is not simply overloaded by two machines dumping at once — that one gets blamed on the washer a lot.
That is bearings, and it is the one fault where the honest answer may be not to repair. Bearing noise comes from the seal failing first and letting water into the bearing housing, which is why chronic overloading shows up years later as a bearing job. On a large washer-extractor the repair means pulling the cylinder and shaft, and on an older machine the cost can approach the price of a replacement. We will tell you which side of that line your machine is on, with the figures, before you commit.
Commercial door locks stay engaged until the control is satisfied that the drum has stopped and the water is out. So a door that stays locked is often a drain or speed-sensing problem wearing a lock's clothing. Once those are cleared, what is left is the lock assembly, its switch, or the harness. There is a manual release procedure on most machines, and we will show your staff where it is so a stuck door does not take a bay out of service while you wait for us.
We service soft-mount and hard-mount washer-extractors, on-premise laundry machines in apartment buildings, gyms, salons and clinics, vended machines in laundromats, and the stacked washer-dryer units used in smaller facilities. That covers coin, card and OPL controls.
Brands we repair in Leander: Speed Queen, Huebsch, UniMac, Dexter, Maytag Commercial, Whirlpool Commercial, Wascomat, Continental Girbau, IPSO, LG Commercial and Electrolux Professional.
The commercial diagnostic is $149, credited toward the repair when you approve it. After the diagnosis you get a written estimate covering parts and labor, and nothing is replaced before you approve it. Control and valve work is usually straightforward; bearing and drive work is not, and on an older machine we will put the repair cost next to the replacement cost so the decision is yours to make with real numbers.
If you run several machines, we would rather look at all of them on one visit than bill you three trip charges across a month.
Our commercial laundry calls in Leander come mostly from apartment laundry rooms off US-183 and Crystal Falls Parkway, gyms and salons along Hero Way, and the newer complexes around Leander Station. Being based in town means a machine that goes down in the morning is usually looked at the same day rather than next week.
Underloading causes imbalance just as reliably as overloading. One heavy item in a large cylinder has nothing to redistribute against, so the drive sees the same signal it would see from a jammed load. If it happens on full loads too, then it is worth looking at the machine.
No. Every manufacturer warns against running with the balance system bypassed, and the reason is not paperwork — a large cylinder extracting out of balance damages bearings, frames and the floor it is bolted to, and can injure someone. If the machine will not spin, the fault gets found instead.
Sometimes, and sometimes not. It depends on the machine's size, age and what else is tired on it. We give you the repair figure and the replacement figure side by side rather than steering you one way.
Yes, both, plus on-premise laundry in gyms, salons and clinics. Coin, card and OPL controls are all fine.
Usually same-day or next morning. Call (737) 388-3867 and tell us the make and what the display is showing — a fault code on the phone often means we arrive with the right part already on the van.
Tell us the make, the capacity, and any fault code on the display. That is normally enough for us to arrive with the right parts on the van.