Two things decide how long a commercial oven lasts around the lake: water and duty cycle. Any oven that makes steam is fighting hard Hill Country water, and scale takes out steam generators here far sooner than the manual predicts. Event kitchens and club kitchens add the second part, weeks of light use and then a banquet at full output. We service restaurants, clubs, marinas and event kitchens across Lago Vista, Point Venture and Jonestown. Commercial diagnostic is 149 dollars and goes toward the repair. EPA certified and insured.

Common causes. On gas it is the igniter, the flame sensor or the gas valve, and on propane a conversion never verified under load. On electric it is an element, a contactor that is not pulling in, or one leg of the supply missing.
What we do. We measure flame signal in microamps on gas and voltage and current on electric. An igniter that glows can still be too weak to open the valve, and that is the failure people misread most often.
Common causes. A convection fan running slow or in the wrong rotation, a burner or element section out, a damaged baffle, or a door that no longer seals on one side.
What we do. We map actual cavity temperature at several rack positions rather than relying on the display, then look at airflow and the door.
Common causes. Hard water again. Scale coats the steam generator and the probes, output falls, and eventually the unit alarms on a water or level fault. Untreated water will do this to any combi in this area.
What we do. We descale the generator properly, check the level probes and the fill valve, and tell you what filtration or treatment this water actually needs. Descaling without fixing the water is a repeating bill.
Common causes. A worn gasket, a sagging hinge, or a latch out of adjustment on a heavy door opened a hundred times a service.
What we do. We replace the gasket and adjust or rebuild the hinge and latch. A door leaking heat shows up as slow recovery and uneven product long before anyone blames the door.
Common causes. A failed motor, a worn bearing, a loose or damaged fan wheel, or a motor cooked by a blocked cooling path.
What we do. We check the wheel and bearing and verify rotation direction, which is wrong more often than people expect after a previous repair.
Common causes. A drifted probe, a probe touching metal, a control calibrated away from true over the years, or a failing contactor cutting actual heat input.
What we do. We measure real cavity temperature through a full cycle and compare against the control before adjusting anything.
Common causes. A probe out of range, a high limit open, a water fault on combi units, or a board damaged by heat, steam and grease.
What we do. We read the fault and verify what it is reporting. Most controller errors are a true fault elsewhere, not a failed controller.
Common causes. Low gas input, a partly failed element, a door that leaks, or a kitchen so short of makeup air that the burners cannot breathe properly during service.
What we do. We time preheat and recovery and, on gas, verify manifold pressure with the rest of the line firing. An oven tested alone in the morning tells you nothing about Saturday night.
Convection ovens, combi ovens, deck and pizza ovens, conveyor ovens, range ovens and cook-and-hold cabinets, gas, propane and electric. Common brands include Vulcan, Blodgett, Garland, Rational, Alto-Shaam, Middleby, Hobart and Imperial.
For seasonal and event kitchens, the oven that sat idle for two months is the one that fails on banquet night. A check before the season costs a fraction of a call during it.
Commercial diagnostic is 149 dollars and is credited toward the repair when you approve the work. The final price depends on the part, whether gas work is involved, and how much descaling a steam unit needs.
Work carries a 3 month labor warranty and installed parts carry a 1 year manufacturer defect warranty. We quote before the work starts.
Lago Vista including the marina and club areas, Point Venture, Jonestown, and out along FM 1431 toward Leander and Cedar Park. We also cover Lakeway and Bee Cave on the south shore.
More often than the factory interval. Without treatment most units here need it on a noticeably shorter cycle, and we will give you a realistic number after seeing the generator.
Usually not. Uneven product is normally airflow or a door seal. The thermostat shows an average, which is why the display can look correct while the rack is not.
Yes. Orifices and regulator have to match propane, and a conversion that was never checked under load shows up as slow preheat and weak recovery.
Same-day wherever we can. Tell us the brand, the model and whether it is gas or electric so we arrive with the right parts.
Call or book online and tell us the oven type, the fuel and any error code. Commercial diagnostic 149 dollars, applied toward the repair.