The number that matters on a fryer is not the setpoint, it is recovery: how fast the oil comes back to temperature after a full basket drops in. A fryer can hold 350 degrees perfectly at idle and still fail a Saturday rush. On propane, which much of Lago Vista runs on, a conversion that was never verified under load is a frequent reason recovery is poor. We service restaurants, clubs, marinas and event kitchens across Lago Vista, Point Venture and Jonestown. Commercial diagnostic is 149 dollars and goes toward the repair. EPA certified and insured.

Common causes. On gas it is burner input: orifices sized for natural gas on a propane appliance, a regulator set wrong, or low supply pressure when several appliances fire at once. On electric it is a weak element or a contactor not pulling in fully. Carbon on the heat exchanger also robs recovery.
What we do. We measure recovery time with a real load, and on gas we verify manifold pressure with the whole line running. A fryer tested alone at idle looks fine and then fails service.
Common causes. A weak or dirty flame sensor, a failed igniter module, a thermopile on standing pilot units, or a gas valve that is not holding. Flame sensing current below about one microamp drops the burner out even though the flame looks fine.
What we do. We measure flame signal in microamps rather than judging the flame by eye, and test the valve and module separately.
Common causes. A failed temperature probe, a control calling for heat past setpoint, low oil level, or carbon buildup insulating the probe. A high limit that trips is doing its job, and resetting it repeatedly without finding the cause is how fryer fires start.
What we do. We verify actual oil temperature against the control, test the probe and the high limit, and we do not simply reset and leave.
Common causes. A drifted probe, carbon on the probe or heat exchanger, or a control that has been adjusted by several people over the years.
What we do. We measure the oil directly at several points and compare against the display before changing anything.
Common causes. A drain valve that no longer seats because of carbon, a worn valve stem or packing, or a cracked weld in the pot. Oil on the floor in a kitchen is a safety problem first.
What we do. We clean and rebuild or replace the valve. A cracked pot is a replacement and we will say so rather than chasing it.
Common causes. On propane this points straight back at the conversion: wrong orifice, wrong regulator setting, or air shutters never adjusted. Soot on the heat exchanger follows and recovery gets worse from there.
What we do. We check orifices and regulator against what the appliance actually runs on and adjust combustion properly.
Common causes. A clogged filter pad or screen, a failed pump motor, an air leak on the suction side, or oil too cold to pump.
What we do. We service the pump and the filter path, and check that the system is being run at the right oil temperature.
Common causes. A probe out of range, a high limit open, a failed power supply, or a controller damaged by heat and grease over time.
What we do. We read the fault and test the probes and limits before replacing a controller, since most controller errors are reporting a real fault elsewhere.
Open pot and tube fryers, gas and propane and electric, floor models and countertop units, with and without built-in filtration. Common brands include Frymaster, Pitco, Henny Penny, Vulcan, Imperial and Dean.
Seasonal kitchens on the lake should know that a fryer sitting idle for months comes back with carbon set hard and seals dried out. That is worth a check before the first busy weekend rather than during it.
Commercial diagnostic is 149 dollars and is credited toward the repair when you approve the work. The final price depends on the part, whether gas work is involved, and how much cleaning the heat exchanger needs.
Work carries a 3 month labor warranty and installed parts carry a 1 year manufacturer defect warranty. We quote before the work starts.
Lago Vista including the marina and club areas, Point Venture, Jonestown, and out along FM 1431 toward Leander and Cedar Park. We also cover Lakeway and Bee Cave on the south shore.
That is a recovery problem, not a thermostat problem. It has to be measured under a real load, and on propane the gas side is the first place to look.
Not as a routine. A repeatedly tripping high limit means something is driving the oil past safe temperature, and that is a fault to find, not to bypass.
Yes. Orifice size and regulator pressure have to match propane, and a conversion done quickly and never tested under load shows up exactly as poor recovery and sooty flame.
Same-day wherever we can. Tell us gas or electric and the brand when you call so we arrive with the right parts.
Call or book online and tell us the brand, whether it is gas, propane or electric, and what the fryer is doing. Commercial diagnostic 149 dollars, applied toward the repair.