A convection oven that will not hold temperature, a combi throwing a boiler error, a deck oven burning one side, or a pilot that will not stay lit before morning prep. TakiDA services commercial ovens for restaurants, bakeries, taprooms, event venues and catering kitchens across Dripping Springs and the surrounding Hill Country, including propane units out past the city gas lines. Insured and certified. Commercial diagnostic $149, applied toward the repair.
Call (737) 388-3867 | Request a visit

Common causes. A temperature probe drifting out of range, a thermostat that no longer modulates, low gas pressure at the manifold, a failing igniter, or door gaskets letting heat out faster than the burners can replace it.
What we do. We log actual cavity temperature against the setpoint through a full cycle with an infrared thermometer, test the probe against its curve, and measure manifold pressure under load. You get the measured drift, not a guess about the oven running cool.
Common causes. A weak thermopile, a dirty pilot orifice, hood draft pulling the flame off the sensor, or a safety valve that will not hold. On propane, a regulator or orifice left set for natural gas.
What we do. We measure thermopile output hot, clean and set the pilot so the flame wraps the sensor, and check hood draw. Where the house runs on propane we verify the conversion, because that single check explains a lot of chronic pilot complaints out here.
Common causes. A seized or failing fan motor bearing, a worn belt on belt-driven models, a loose or warped fan wheel, or a motor relay that has quit.
What we do. We measure motor current against the nameplate, check the wheel and belt, and test the relay. An oven that bakes unevenly with a healthy burner is almost always airflow, and that is the first thing we look at.
Common causes. A weak convection fan, a baffle removed during cleaning and never replaced, a burner out of adjustment, a blocked flue, or racks overloaded so air cannot move.
What we do. We map the cavity temperature at several points, check the baffles and burner flame pattern, and verify the flue is clear. The fix is often a baffle and a loading change rather than a part.
Common causes. Scale in the steam generator from hard water, a failed water level probe, a clogged inlet solenoid, a drain blockage, or a water filter long past its service life.
What we do. We descale the generator, clean the level probes, clear the inlet and drain, and replace the filter. Combi ovens in this area live or die on water treatment, and we will tell you the realistic descale interval for your water rather than the manual's.
Common causes. Worn hinges, a torn or hardened gasket, a bent door frame, or a latch that no longer pulls the door home.
What we do. We replace gaskets, hinges and latch hardware, and square the door. A leaking oven door costs real gas every hour it runs, so it pays for itself faster than most repairs.
Common causes. A probe circuit open, a failed transformer, a loose harness in a hot cabinet, a membrane keypad delaminated from steam, or a board damaged by heat.
What we do. We read the code, confirm supply voltage and the transformer, and test the circuit the code names before touching the board. Commercial oven boards are expensive and we do not order one on a code alone.
Common causes. Wrong orifices for the fuel, air shutters out of adjustment, a cracked manifold connection, a failing safety valve, or a flue that is partly blocked.
What we do. We stop, isolate the gas, leak-test the connections, and set combustion so the inner cone is sharp and blue. A gas smell is treated as urgent and does not wait for a convenient appointment.
Full-size and half-size convection ovens, combi ovens, deck and pizza ovens, conveyor ovens, rack and rotisserie ovens, proofers and holding cabinets, and range ovens under commercial cooktops, on natural gas, propane and electric. We service Vulcan, Blodgett, Garland, Imperial, Southbend, Bakers Pride, Rational, Alto-Shaam, Middleby Marshall and Lincoln equipment for restaurants, bakeries, taprooms, event venues and catering kitchens.
The commercial diagnostic is $149 and it is credited toward the repair when you approve it. Gaskets, hinges, thermopiles, igniters, probes and fan belts are the moderate end. Gas valves, convection motors, combi boiler work and control boards are the expensive end, and on an older oven we will give you the repair number against a replacement so the choice is informed. You get a written estimate with parts, labor and tax before any work starts, and it stays good for 30 days. Labor carries a 3 month warranty and installed parts carry one year against manufacturer defects.
We cover Dripping Springs and the businesses around it, from the restaurants and bakeries along Mercer Street to the wineries, distilleries and event venues out along Ranch Road 12 and Highway 290 West, plus the retail along the 290 corridor. Nearby Driftwood, Henly and Wimberley are inside our normal route, and Bee Cave, Lakeway and Austin are a short run from here.
Maybe, and maybe the probe has drifted or the convection fan has slowed. We measure the real cavity temperature in several places before replacing anything, because an oven that is genuinely at 350 and still baking unevenly has an airflow problem, not a thermostat problem.
More often than the manual says. On untreated hard water a steam generator can scale up in a few months. We will look at yours and give you a realistic interval plus a filter recommendation.
Tell us your window when you call. We would rather work around your rush than through it, and an oven down before a catering event gets priority.
Commercial calls take priority and same-day is usually possible. Anything involving a gas smell is urgent.
Tell us the brand, the oven type, whether it is gas, propane or electric, and what it is doing, and we will arrive with the parts most likely to get you back into service.