A dryer tumbling with no heat, loads taking three cycles to dry, a gas unit that lights and drops out, or a lint and duct situation that has become a fire risk. TakiDA services commercial dryers for salons and spas, gyms, country clubs, short-term rentals, event venues and apartment laundry rooms across West Lake Hills and the surrounding 78746 area. Insured and certified. Commercial diagnostic $149, applied toward the repair.
Call (737) 388-3867 | Request a visit

Common causes. On gas, a failed igniter, flame sensor or gas valve coil, or a high-limit that has tripped. On electric, a burnt element or one leg of the 240 volt supply lost. On either, a thermal cutoff opened by restricted airflow.
What we do. We watch an ignition sequence end to end and measure flame sensor current in microamps rather than guessing at the symptom. Before any part goes in, the airflow gets checked, because a cutoff that opened once because the duct is blocked will open again the day after a new one is fitted.
Common causes. This is airflow almost every time. A duct packed with lint, a flexible run crushed behind the machine, a screened or blocked vent cap outside, a long duct carrying too many elbows, or a shared stack serving several machines at once.
What we do. We measure exhaust temperature and airflow at the machine and then follow the duct to where it leaves the building. Properties around here often have the laundry buried in the middle of the floor plan with a long run to an outside wall, and that run is where the time goes, not inside the dryer.
Common causes. A dirty or misaligned flame sensor, a weak igniter, a failing valve coil, or insufficient makeup air in a closed laundry room.
What we do. We measure flame sensor current in microamps and watch the burner through several cycles. A borderline sensor reading tells us the part is marginal rather than dead, and that is a measurement, not a guess.
Common causes. A broken belt, a seized idler pulley, worn drum rollers or glides, a failed drive motor, or a door switch the control still reads as open.
What we do. We check belt and idler, turn the drum by hand to feel the rollers, and test the motor and the door switch. A door switch costs almost nothing and produces exactly the same complaint as a dead motor, so it gets tested before anything expensive is quoted.
Common causes. Worn drum rollers or a tired rear bearing, a glazed belt, a blower wheel starting to fail, or debris loose in the blower housing.
What we do. We work out which component is making the noise while the machine runs, then replace the rollers, bearing, belt or blower. A rumble that has been ignored for months usually costs more by the time it is looked at, because the drum has been running on a flat roller long enough to mark the shaft.
Common causes. A jammed coin mechanism, a failed reader or harness, a vend board that has lost its signal to the control, or a machine sitting in lockout from an earlier fault.
What we do. We test the vend path from reader through to control, clear the jam or the lockout, and confirm a full cycle runs after payment. In a shared laundry at a rental or a club the cost of this is not the lost coin, it is the complaint that follows, so we verify the whole path rather than just freeing the mechanism.
Common causes. Venting restricted enough to overheat the cabinet, a failed cycling thermostat, a blower wheel slipping on its shaft, or a bypassed lint screen letting lint reach the blower.
What we do. We measure exhaust temperature across a full cycle, clear the vent and test the thermostats and cutoff. A machine that trips repeatedly is telling you about heat it cannot get rid of, so replacing the cutoff without clearing the duct just resets the countdown.
Common causes. A transition duct that has come apart or split, a flexible run crushed behind a stacked unit, a missing or torn lint screen, or a shared vent carrying more than it was built for.
What we do. We reconnect and secure the duct in rigid or semi-rigid metal where it should be, replace the screen and clear the run. Loose lint around a gas dryer is a fire risk and not a housekeeping complaint, and in a laundry closet tucked inside a house or a club that risk sits under occupied rooms.
Single-pocket and stack dryers, gas and electric, on-premise laundry for salons, spas, gyms, country clubs and short-term rentals, card and coin vended dryers in apartment laundry rooms, and stacked washer-dryer units. We service Speed Queen, Huebsch, Wascomat, Electrolux Professional, Maytag Commercial, Whirlpool Commercial, Dexter, ADC and LG Commercial.
The commercial diagnostic is $149 and it comes off the repair when you approve it. Vent clearing, belts, rollers, idlers, igniters, flame sensors, thermostats, cutoffs, door switches and vend parts are the moderate end and settle most of these calls. Gas valves, drive motors, blowers and control boards are the expensive end. On an older machine we hand you the repair figure next to a replacement figure.
We cover West Lake Hills and the 78746 area around it, including the businesses along Bee Caves Road and the Loop 360 corridor, plus Westlake Highlands and Rollingwood. Lakeway and Bee Cave are inside our normal route, and Austin is a short run from here.
Usually not. In a commercial laundry room slow drying is nearly always the vent, the duct run or the cap outside. We measure airflow and exhaust temperature first, so you know whether you have a machine problem or a duct problem before anyone spends money on parts.
Quarterly in a busy laundry room, and more often for a salon or spa running towels all day. It is the cheapest insurance there is against both slow drying and a lint fire, and it is the job that gets skipped until something else goes wrong.
Yes. Tell us who holds the key or code and we will arrange it, and we will report back on exactly what we found rather than leaving you to guess.
Commercial calls go to the front of the schedule and same-day is usually possible. Lint around a gas dryer, or a machine overheating and tripping its cutoff, is treated as urgent and does not wait for a convenient slot.
Tell us the brand, the model, whether it is gas or electric, vended or on-premise, and how long a load currently takes, and we will arrive with the parts most likely to finish the job on the first visit.