Loads coming out damp, a pocket that will not heat, dryers that all slowed down at once, or a burner that will not light. We repair commercial tumblers and apartment laundry room dryers in Cedar Park, gas and electric. The $149 commercial diagnostic is credited toward the repair.

On a machine running an automatic cycle, the dryer decides for itself when the load is finished. When that judgement goes wrong, you get a machine that runs its full cycle, shuts down neatly and hands back damp linen. That is a different fault from a dryer that will not heat, and it gets looked at differently — the sensing circuit and the control, not the burner.
Drying is airflow before it is heat. A blower wheel that has worked loose on its shaft, or a blower housing packed solid with lint, will leave the drum turning and the heat on while almost nothing moves through the machine. We measure airflow instead of guessing at it, because a weak dryer and a dryer with no heat look the same from the front.
Every dryer in the room has to pull its air from somewhere. In a closed laundry room with no makeup air, running two or three machines together puts the room under negative pressure, and each one starves the others. The symptom looks like slow drying on every machine at once, which is the clue — a worn part fails on one machine, not on all of them.
A stacked dryer is two machines sharing a frame, and usually a vent. Each pocket has its own heat source and its own controls, so one side going cold points at that side’s circuit rather than at the pair. The shared vent is the exception, and that is the first thing worth ruling out.
A dryer that runs past the end of its cycle, or that never counts down at all, is burning gas or power for nothing and holding up the room. This is a control fault, and on vended machines it also affects what the customer paid for.
The door circuit has to be made up for the machine to run, so a worn switch or a latch that has drifted out of alignment will drop the machine mid-cycle. It is a cheap fix, and worth ruling out before anyone starts on the control board.
On a gas machine, nothing happening at the burner at all is a different fault from a burner that lights and then drops out. We check that the ignition circuit is being called in the first place, then the ignitor or spark module, then the gas valve. Gas work is finished with a leak check on anything we opened.
Larger tumblers reverse the drum so the load keeps turning over instead of roping up into a ball. When reversing stops, the outside of the load dries and the middle stays wet, and the cycle time goes up to compensate. The command comes from the control and is carried out by contactors or a drive.
We work on single-pocket and stacked commercial tumblers, the vended dryers in coin and card laundries, and the machines in apartment laundry rooms. Common brands in Cedar Park include Speed Queen, Huebsch, Unimac, Dexter, Wascomat, American Dryer, Maytag Commercial and Whirlpool Commercial Laundry, in both gas and electric.
Tell us when you book whether the machine is gas or electric and whether it is stacked. That changes what we bring and how long we need on site.
The commercial diagnostic is $149 and comes off the repair when you approve it. Ignitors, switches, thermostats, belts, rollers, door latches and control components are modest. A motor, a blower assembly or duct work on the roof is a different conversation, and we tell you which one you are looking at before we start.
Venting is where we draw a line. We diagnose it, we will open and clear a transition, and we tell you plainly what the duct is doing. A full exhaust cleaning on a long or roof-mounted run is specialist work and we hand that to a certified contractor rather than half-do it.
Dryer work takes us to the laundry rooms across Cedar Park — the apartment communities off Cypress Creek and Lakeline, the properties along Parmer and Brushy Creek, the gyms and salons on Whitestone, and the laundries near the Bell Boulevard corridor. We are based in Leander, about twenty minutes away, which matters when half the machines in a room are down.
Usually airflow rather than heat. If that machine sits at the far end of a shared duct, or its own blower or lint path is restricted, it will dry slower than its neighbours while everything else about it tests fine.
Yes. Dryers pull a large volume of air out of the room, and if nothing replaces it the machines fight each other. If every dryer in your room slowed down at the same time, that is the first thing worth looking at.
That is the main thing we settle on the first visit. Replacing parts in a machine that is choking on its own exhaust fixes nothing, and we would rather tell you that than sell you a part.
Yes, including the ones where only one pocket has gone cold. The two halves are more separate than they look.
Same-day is often possible. Tell us the make, the model, whether it is gas or electric and what the display shows, and we will bring the likely parts.
Tell us the make and model, whether the machine is gas or electric, and whether it is a stacked unit. That decides what goes on the van.