A washer that will not spin out, a machine walking across the floor on every extract, a card or coin unit that takes payment and does nothing, or a leak running under a laundry room floor. TakiDA services commercial washers for salons and spas, gyms, short-term rentals, event venues, apartment laundry rooms and laundromats across Dripping Springs and the surrounding Hill Country. Insured and certified. Commercial diagnostic $149, applied toward the repair.

Common causes. A door lock the control reads as open, a failed drain pump so the machine never gets a dry-to-spin signal, worn belts on belt-driven machines, a failed inverter or drive motor, or an out-of-balance load the control keeps aborting.
What we do. We read the stored fault code, test the door lock circuit, confirm the machine fully drains, and check belts and drive. We measure motor current under load rather than assuming the motor, because a drain fault and a drive fault look identical from the front of the machine.
Common causes. Worn shock absorbers or suspension rods, a failed bearing, loose or missing floor anchors on a hard-mount machine, or a basket out of balance.
What we do. We check the suspension and anchors, spin the basket by hand to feel for bearing roughness, and listen through an extract. A machine allowed to keep walking will eventually take out its own bearings and spider, so this one is worth catching early.
Common causes. Clogged inlet valve screens, a failed fill valve coil, a closed supply valve, low water pressure, or a pressure switch or level sensor that already thinks the tub is full.
What we do. We measure supply pressure at the machine, clean the inlet screens, test the valve coils, and clear the level sensing hose. On well water the screens block far faster than people expect, and that check comes first.
Common causes. A worn door boot or gasket, a leaking drain valve, a split hose or clamp, a cracked tub seal, or a drain line that backs up under the volume of a full machine.
What we do. We run the machine and find the leak while it is leaking rather than guessing from the stain. Boot, valve, hose or seal gets replaced, and we check the building drain can actually take the discharge rate.
Common causes. A jammed coin mechanism, a failed card reader or its harness, a vend board that has lost its signal to the control, or a machine in a lockout state from a previous fault.
What we do. We test the vend path from the reader through to the control, clear the jam or lockout, and verify a full cycle runs after payment. In an unattended laundry room a machine that takes money and does nothing costs you more in goodwill than in parts.
Common causes. A door lock or switch fault, a thermistor out of range, an inverter overtemperature, a water level fault, or a control board with a failed output.
What we do. We read the code against the model's service chart and test the circuit it names. Codes point at a symptom, not a part, and we treat them that way before anything gets ordered.
Common causes. Hard water with no softening, overdosed or underdosed detergent, a failed chemical injection pump on an on-premise machine, a cold water-heater supply, or biofilm in the boot and dispenser.
What we do. We measure the incoming water temperature, verify the chemical pumps actually draw, and clean the boot and dispenser. In this area hard water is usually a real part of the answer, and we will tell you that plainly rather than replacing parts around it.
Common causes. A failed bearing or seal, a worn belt, an object trapped between tub and basket, or a drain pump impeller full of lint and debris.
What we do. We clear the pump, check the belt and basket, and listen for the bearing at speed. A bearing on the way out gets a plain recommendation, because on some machines that repair costs more than the machine is worth and you should know that before we start.
Front-load and top-load commercial washers, soft-mount and hard-mount machines, on-premise laundry for salons, spas, gyms and short-term rentals, card and coin vended machines in apartment laundry rooms and laundromats, and stacked washer-dryer units. We service Speed Queen, Huebsch, Wascomat, Electrolux Professional, Maytag Commercial, Whirlpool Commercial, Dexter, Continental Girbau and LG Commercial.
The commercial diagnostic is $149 and it is credited toward the repair when you approve it. Door boots, inlet valves, drain pumps and valves, belts, shocks, hoses, switches and vend components are the moderate end and are most of what these machines need. Bearings, drive motors, inverters and control boards are the expensive end, and on an older machine we will give you the repair number against a replacement so the call is yours. You get a written estimate with parts, labor and tax before any work starts, and it stays good for 30 days. Labor carries a 3 month warranty and installed parts carry one year against manufacturer defects.
We cover Dripping Springs and the businesses around it, from the salons, spas and gyms in town to the short-term rentals and event venues out along Ranch Road 12 and Highway 290 West, plus apartment laundry rooms along the 290 corridor. Nearby Driftwood, Henly and Wimberley are inside our normal route, and Bee Cave, Lakeway and Austin are a short run from here.
Yes. Tell us who holds the key or the code and we will arrange it, and we will report back on what we found so you are not relying on a tenant's description of the problem.
Often not. Hard water, detergent dosing and water temperature account for most of it, and all three are measurable. We check those before suggesting a repair, because replacing parts will not fix water chemistry.
Sometimes. On a heavy commercial machine it usually is, and on a light-duty unit it usually is not. We give you the number for the repair and let you weigh it against a replacement rather than deciding for you.
Commercial calls take priority and same-day is usually possible. A laundry room down for a salon, spa or rental turnover gets treated as urgent.
Tell us the brand, the model, whether it is vended or on-premise, and the fault code if the display shows one, and we will arrive with the parts most likely to finish the job on the first visit.