A convection oven that will not hold temperature, a combi throwing a boiler error, a deck oven burning one side, or a pilot that will not stay lit before morning prep. TakiDA services commercial ovens for restaurants, cafes, bakeries, country clubs and catering kitchens across West Lake Hills and the surrounding 78746 area. Insured and certified. Commercial diagnostic $149, applied toward the repair.
Call (737) 388-3867 | Request a visit

Common causes. A temperature probe reading out of range, a thermostat that no longer modulates, low gas pressure at the manifold, an igniter on its way out, or door gaskets letting heat escape faster than the burners can make it.
What we do. We log real cavity temperature through a full cycle instead of trusting the dial, check manifold pressure, and test the probe and thermostat against measured values. A kitchen that fires the oven hard for one service and leaves it cold the rest of the day puts the whole strain on ignition and pressure, and that is usually where this one lives.
Common causes. A weak thermopile, a dirty pilot orifice, hood draft pulling the flame off the sensor, or a safety valve that will not hold.
What we do. We measure thermopile output hot, clean and set the pilot so the flame wraps the sensor, and check hood draw. Where the exhaust is blowing the pilot out, replacing the thermopile would have solved nothing.
Common causes. A fan motor bearing seizing, a worn belt on belt-driven models, a fan wheel loose or warped, or a motor relay that has quit.
What we do. We measure motor current against the nameplate, check the wheel and belt, and test the relay. A wheel rubbing its housing sounds exactly like a dying motor from outside the oven, so the cheap check comes first and the expensive part only after the numbers say so.
Common causes. A weak convection fan, a baffle taken out for cleaning and never put back, a burner out of adjustment, a partly blocked flue, or racks loaded so tight that air cannot move.
What we do. We map cavity temperature at several points, check the baffle and burners, and look at how the oven is actually loaded. A missing baffle is remarkably common and costs nothing to correct, and it produces exactly the complaint people assume means a failing oven.
Common causes. Scale in the steam generator from hard water, a failed water level probe, a clogged inlet solenoid, a drain blockage, or a water filter long past its service life.
What we do. We descale the generator, clean the level probes, clear the inlet and drain, and replace the filter. Combi ovens in this area live or die on water treatment, and we will tell you the realistic descale interval rather than the manual's.
Common causes. Worn hinges, a gasket torn or gone hard, a bent door frame, or a latch that no longer pulls the door home.
What we do. We replace gaskets, hinges and latch hardware and square the door. A door leaking heat burns gas all service and makes the whole cavity read uneven, so this gets fixed before anyone starts adjusting burners to compensate for it.
Common causes. A probe circuit open, a failed transformer, a harness loose inside a hot cabinet, a membrane keypad delaminated by steam, or a board cooked by heat.
What we do. We read the code, confirm supply voltage and the transformer, and test the circuit the code names before condemning a board. Boards are the expensive guess, and in a hot cabinet a loose connector mimics a dead board often enough to be worth ruling out first.
Common causes. Air shutters out of adjustment, a cracked manifold connection, a safety valve failing, or a flue partly blocked.
What we do. We stop, isolate the gas, leak-test every connection and set combustion so the inner cone is clean and stable. This is the one call where nothing else gets worked on until the gas side is proven safe, and we will shut equipment down and say so rather than leave it running.
Full-size and half-size convection ovens, combi ovens, deck and pizza ovens, conveyor ovens, rack and rotisserie ovens, proofers and holding cabinets, and range ovens under commercial cooktops. We service Vulcan, Blodgett, Garland, Imperial, Southbend, Bakers Pride, Rational, Alto-Shaam, Middleby Marshall and Lincoln equipment for restaurants, cafes, bakeries, country clubs and catering kitchens.
The commercial diagnostic is $149 and it comes off the repair when you approve it. Gaskets, hinges, thermopiles, igniters, probes and fan belts sit at the moderate end. Gas valves, convection motors, combi boiler work and control boards are the expensive end. On older equipment we put the repair figure beside the replacement figure and let you decide with both in front of you.
We cover West Lake Hills and the 78746 area around it, including the businesses along Bee Caves Road and the Loop 360 corridor, plus Westlake Highlands and Rollingwood. Lakeway and Bee Cave are inside our normal route, and Austin is a short run from here.
Possibly, and equally possibly the probe has drifted or the convection fan has slowed. We measure real cavity temperature at several points before replacing anything, because an oven genuinely sitting at 350 and still baking badly has an airflow problem, and a new thermostat will not touch it.
More often than the manual suggests. On water this hard a steam generator can scale up within a few months of regular use. We will look at yours, give you a realistic interval and recommend a filter, because the filter is cheaper than the generator every single time.
Tell us your window when you call. We would rather work before doors open or after last cover than through the middle of a service, and an oven down ahead of a catering event or a private function moves up the list.
Commercial calls go to the front of the schedule and same-day is usually possible. Anything involving a smell of gas is urgent and gets handled immediately, not scheduled.
Tell us the brand, the oven type, whether it is gas or electric, and what it is doing, and we will arrive with the parts most likely to get you back into service.