Cloudy glassware, racks taking far longer than they used to, a wash tank losing temperature through service or a detergent bill climbing on its own — we service commercial dish machines across Round Rock, from Old Town and Main Street to La Frontera and the I-35 corridor. Deliming included. Insured for commercial premises. Commercial diagnostic $149, credited toward the repair.

There are two different problems here and only one of them can be fixed, so it is worth telling them apart before spending money. Film from mineral deposit sits on the surface and comes off with an acid rinse or a vinegar soak, and it points at water hardness, rinse aid and wash temperature. Etching has eaten into the glass itself and nothing will bring it back: it comes from the combination of soft water, too much detergent and high temperature over many cycles. If a test glass clears with acid, we have a machine and chemistry problem worth solving. If it does not, the machine may be fine and the glasses are the casualty of how it has been run.
On a high temperature machine the cycle will not finish until the final rinse reaches the temperature it is required to hit, so anything that slows the booster stretches every rack. Scale on the booster element is the usual culprit here, along with incoming water that has cooled because the water heater is struggling or the run is long. There is also a human version of this: staff waiting between racks because they know the machine needs it. Either way, we measure booster recovery rather than guessing, because that number tells you how many racks an hour you can actually do.
Some steam is expected, a cloud is not. If a hood machine is releasing a great deal of steam into the kitchen it usually means the rinse is running hotter than it should, the vent cowl or condensate arrangement is missing or blocked, or the machine is being opened the instant the cycle ends rather than after the short dwell it is designed for. Beyond the discomfort, that steam carries into ceiling tiles and electrics. We check the rinse temperature and the venting together.
A conveyor that catches racks is mechanical, and the usual places are the pawl bar or drive mechanism that pushes the racks along, worn or warped racks that no longer sit square, and curtains hanging badly so a rack catches as it passes. Running it with a jam does damage quickly. These are serviceable parts and the adjustment is part of routine work, and while we are in there the curtains are worth replacing if they are cracked, because they also control where the water stays.
The wash tank is heated to a set temperature, and every rinse adds fresh water to it. During a heavy run that happens faster than the tank heater can recover, and the wash drops below the range where detergent works. The questions are whether the tank element and its contactor are good, whether scale has insulated the element, and whether the incoming water is as hot as the machine expects. On a busy line this one shows up as results getting worse through the evening rather than as a fault.
Dispensers meter detergent against a conductivity probe in the tank, and when that probe scales up it reads low and the dispenser keeps adding. The result is a chemical bill that grows quietly and glassware that starts etching. A fill valve passing slightly when it should be closed does the same thing by diluting the tank. Both are inexpensive to put right, and the saving usually pays for the visit.
A trip that lands exactly when the booster energises points at the booster element breaking down to ground, or at a circuit that is marginal for the load. On three phase machines, a lost leg produces slow heating and overheating contactors instead. This is measured rather than reset, because a booster element faulting to ground is a shock risk in a wet environment.
On a chemical machine, too much sanitizer is a problem as well as too little: it costs money, it can leave a residue and taste on ware, and it is as much an inspection issue as under dosing. The causes are a peristaltic pump tube that has softened and is passing more than it should, a pump that has lost its calibration, or a dispenser siphoning when the machine is idle. All are cheap parts, and the machine should be set and then verified with strips rather than assumed.
We service under-counter, door type and hood machines, conveyor and rack machines, glasswashers and bar washers, in both high temperature and chemical sanitizing configurations, from Hobart, Jackson, CMA, Champion, Ecolab, Moyer Diebel, Insinger and the Atosa and Avantco machines common in smaller kitchens. That covers booster heaters, tank elements and contactors, wash and rinse pumps, fill and drain valves, level probes and floats, wash and rinse arms, conveyor drives and curtains, chemical pumps and pickup lines, gaskets and door hardware, plus deliming and water quality advice. We are insured for commercial premises.
The commercial diagnostic is $149 and it comes off the repair when you approve it. You get a written price for parts and labor before anything is replaced. Valves, probes, thermostats, contactors, arms and bearings, curtains, gaskets, conveyor adjustment, chemical pump tubes and deliming are all modest. Booster and tank heaters, wash motors and control assemblies are the expensive end. If a machine needs several of those at once we will put the number next to a replacement rather than working through it one part at a time.
A large share of commercial dishwasher calls are scale, chemical delivery or a wash arm, and those are cheap fixes that put your results and your sanitation numbers back where they belong.
Along the I-35 corridor, La Frontera and the outlets, and at the larger venues east of town, the machines are conveyor and high volume door type units where throughput is the measure that matters. Booster recovery, tank temperature and chemical dosing are the recurring issues there, and a machine that has quietly slowed costs a dish room staff hours every week before anybody calls it a fault.
Around Old Town, Main Street and Mays the machines are smaller under counter and door type units in restaurants and bars with no spare capacity, so when one goes down the kitchen is washing by hand within the hour. Those buildings often have long hot water runs, which matters when a rinse temperature is marginal rather than failed. We also service dish machines in school and institutional kitchens across Round Rock, where sanitation records are kept and a failed rinse temperature has to be dealt with the same day. Round Rock is an easy run from Leander.
If it is mineral film, yes, and the machine and chemistry are worth adjusting. If it is etching, the glass is permanently damaged. A vinegar or acid test on one glass tells you which you have in minutes.
Usually the booster. The cycle waits for the final rinse to reach temperature, so a scaled element or cooler incoming water stretches every rack. We measure recovery rather than guess.
Often the conductivity probe has scaled and reads low, so the dispenser keeps adding. A fill valve passing slightly does the same thing by diluting the tank. Both are inexpensive.
Where the schedule allows, yes. Deliming in particular is better done when the kitchen is not running. Tell us your hours when you call.
Often the same day, and we treat a dish machine down as urgent because it stops a kitchen. Call (737) 388-3867 with the make and model and what it is doing.
Tell us the make and model, whether it is high temperature or chemical sanitizing, and what it is doing — slow racks, cloudy ware, temperature not holding, or dosing wrong. If an inspection flagged it, say so and we will prioritise it. Call (737) 388-3867 or book online and we will confirm a time for Round Rock.