A disposal is a small motor bolted to a drain, and almost everything that goes wrong with it is either a jam, a seal or the switch feeding it. The part most people assume has failed is usually fine, which is why it is worth ten minutes of checking before anyone buys a new one.

Something is wedged between the impeller and the shredder ring, and the motor is stalled against it. The hum is power reaching a motor that cannot turn. Holding the switch on in that state is what actually kills the unit, so switch it off, free the jam from the bottom with the hex key, then press the reset.
No hum means no power at the motor. That is the thermal overload still latched out, a tripped breaker, the wall switch, or the connection at the unit. We start at the outlet under the sink rather than assuming the disposal is dead.
Where the drip starts tells you what failed. At the sink flange it is the mounting seal and the putty under it; at the side inlet it is the dishwasher hose connection; from the bottom housing it is the internal seal, and that one means the unit has reached the end rather than needing a part.
The overload is tripping for a reason: a partial jam still in there, worn bearings loading the motor, or a motor winding on its way out. Repeated resets are a symptom, not a fix, and continuing to press it is how a cheap repair turns into a replacement.
Usually the drain line beyond the unit rather than the disposal itself, especially where the trap arm has a long run. If both bowls fill, the blockage is downstream of the tee and the disposal is simply the thing that revealed it.
A metal object in the chamber, a broken impeller, or bearings that have worn. Something loose rattles intermittently; bearings give a steady grinding that rises with the motor and gets worse week by week.
The knockout plug in the dishwasher inlet was left in place. New units ship with it sealed and it has to be driven out before the hose is connected. Very common, trivial to put right.
Air switches use a bellows and a tube to a pneumatic actuator, and both perish. A wall switch simply wears out. Either way the disposal is fine and the control is not.
Continuous feed and batch feed units, half to one horsepower, standard and sound-insulated models, with wall switches, air switches and dishwasher connections. Brands we see here include InSinkErator, Waste King, Moen, KitchenAid, Whirlpool and GE.
The residential diagnostic is $99, credited toward the repair once you approve it. Jams, seals, switches and connections are usually a straightforward fix. Where the motor or the lower housing has failed we tell you that replacing the unit is the better buy instead of quoting a repair that does not make sense.
West Lake Hills, Rollingwood, Westlake Highlands, Barton Creek and the streets off Bee Cave Road and Capital of Texas Highway, plus the rest of our Central Texas area.
Probably not. The thermal overload is designed to cut in exactly for that. Free the jam, press the reset underneath, and most units come back. If it trips again straight away, something is still caught.
Jams, seals, flanges and switches are worth repairing every time. A failed motor or a leak from the body of the unit is not, and on a budget model the replacement often costs less than the part.
They are genuinely quieter and the stainless grinding components last longer. Whether that is worth the difference depends on how hard the kitchen uses it.
Grease, fibrous peelings, coffee grounds, bones and anything starchy in quantity. Cold water while it runs helps everything through; hot water does the opposite with fat.
Same-day is often available and next-day is normal. Call and we will tell you what is open.
It is a clean division. Everything above the motor is a repair: jams, the sink flange and its seal, the dishwasher inlet, the splash guard, the switch and the mounting assembly. All inexpensive parts and a single visit. Anything involving the motor or the lower body is not, because reaching it costs more in labour than a new unit does on most models.
The exception is the heavier horsepower units with stainless grinding components, which are built to be rebuilt and usually mounted into a more substantial sink assembly. Those are worth the work. We tell you which category yours falls into before quoting anything.
A disposal fitted carelessly makes trouble for years afterwards. The mounting ring must seat properly or it weeps slowly into the cabinet where nobody sees it. The discharge wants a clean run to the trap without a dip that holds standing water. The dishwasher knockout has to come out, and the hose needs a high loop so wastewater cannot drain back into the machine.
The electrical side matters as well. A hardwired unit should have an accessible disconnect, and a plug-in unit wants an outlet under the sink that is not shared with half the kitchen. Where we find these wrong during a repair we correct them, rather than leaving new work sitting on top of an old installation fault.
Tell us whether it hums, is silent, or leaks, and where the water appears if there is any. Call (737) 388-3867 or book online. The $99 diagnostic is credited toward the repair.
We repair all major residential appliance brands across Central Texas, including Whirlpool, GE, Samsung, LG, Maytag, Frigidaire, KitchenAid, Amana, Bosch, Electrolux, Hotpoint, Kenmore, Haier, Fisher & Paykel, Sub-Zero, Wolf, Viking, Thermador, JennAir, Dacor, U-Line, Marvel, Miele, and GE Monogram.