A dryer that leaves the clothes damp, shuts off part way through or stops heating is usually an airflow problem before it is a parts problem. We repair gas and electric dryers across Georgetown — Sun City, Wolf Ranch, Water Oak, Berry Creek, Serenada, Cimarron Hills and the older blocks around the Square — and we do the vent work with it. The diagnostic is $99 and it comes off the repair.

This is the most common dryer complaint we get in Georgetown and it is almost never the dryer. A dryer dries by moving air: it heats the air, pulls it through the load and pushes the moisture out through the vent. Heat the air and give it nowhere to go, and the clothes get hot and stay wet. In a lot of Georgetown homes the laundry room sits in the middle of the floor plan, so the duct runs a long way through the attic before it reaches a wall or the roof, and every extra foot and every elbow costs airflow. Sags in flexible duct collect lint and condensation, and the outside flap gets painted shut or blocked by a nest. We check the vent run end to end and measure the airflow before we open the machine.
That pattern is the dryer protecting itself. When air cannot leave, the heat builds behind the drum and a high limit thermostat opens to stop the burner or element. Once things cool it closes again and the dryer will run for a few more minutes. People live with this for months, and the whole time the real damage is being done: the thermal fuse eventually blows for good, and on a gas machine the burner is cycling far more than it was designed to. The fuse is a cheap part, but replacing it without fixing the airflow just sets the clock running again.
What we look at depends on how the dryer is powered, and this is where guessing gets expensive. An electric dryer runs on two 120 volt legs. The motor only needs one of them, so if a leg is lost at the breaker, the cord or the terminal block, the drum will turn happily and the heater will do nothing. We check both legs under load, not at rest, because a loose connection reads fine until current goes through it. On a gas dryer the chain is the igniter, the valve coils, the flame sensor and the thermal fuse, and each one fails in a way you can tell apart by watching the burner compartment through a cycle. Either way it is a measurement, not a parts swap.
Stop using it and call. Lint is fuel, and the places it collects are the heater housing, the blower wheel and the inside of the cabinet below the drum. A smell means it is reaching something hot. The other cause is mechanical: an idler pulley that has seized and is being dragged by the belt, or a glazed belt slipping on the drum. Both smell like something burning and both are inexpensive to fix. Neither is worth taking a chance on, because a dryer fire starts in exactly this part of the machine.
A thump that comes and goes with how much is in the drum is usually the drum support rollers. They are plastic, they wear flat on one side, and the drum then drops onto the flat spot once per revolution. A scrape that is constant regardless of load is different: either the felt seals at the front or rear of the drum have worn through and the drum is riding on metal, or something has made its way past the lint filter and is sitting in the blower wheel. We turn the drum by hand with the belt off, which tells us immediately which of the three it is.
Inside the drum there are three or four raised baffles that lift the load and drop it. When a baffle works loose or the lip breaks off, the clothes slide along the wall in a lump instead of tumbling, and nothing dries evenly no matter how long the cycle runs. It also sounds exactly like an overloaded dryer, which is why people keep running smaller loads and wondering why it did not help. Baffles are a modest part and a straightforward job.
Sensor dry works off two metal strips inside the drum, usually just behind the lint filter opening, that measure how well the laundry conducts across them. Fabric softener and dryer sheets leave a film on those strips, and the film insulates them, so the control reads a dry load and ends the cycle early. The fix is cleaning the bars properly, not a new control board, and we have seen boards sold for exactly this. If the bars are clean and the behaviour continues, then the sensor circuit is worth testing.
On an electric dryer that usually means the heating element has broken and a piece of it is touching the housing, which puts a fault straight to ground. The dryer may run for a minute or two before it goes. The other candidate is a motor winding that has shorted, and the way to tell them apart is an insulation check on each with the circuit isolated. What matters here is not to keep resetting the breaker to see if it holds. If a dryer trips a breaker twice, something inside it is faulting to ground and it needs to be looked at before it is used again.
We work on the brands that are actually in Georgetown laundry rooms: Whirlpool, Maytag, LG, Samsung, GE, Frigidaire, Amana, Kenmore and Electrolux, along with Speed Queen and the Bosch and Electrolux compact units. That covers gas and electric, top control and front control, stacked pairs, the 24 inch compact dryers that go into Sun City casitas and condos, and ventless heat pump dryers. We also do the vent work, which on a dryer call is usually more than half the answer: duct rerouting, rigid replacement for crushed flexible duct, and hood replacement. Parts for the mass market brands are on the shelf or a day out.
The residential diagnostic is $99 and comes off the repair when you approve it. You get a written price for parts and labor before anything gets replaced. Thermal fuses, thermostats, igniters, valve coils, belts, idler pulleys, rollers, drum seals and baffles are all modest parts. Motors, blower assemblies and control boards are not, and on a dryer past twelve years we will tell you plainly when a new machine is the better use of the money.
A real share of dryer calls end at the vent, and we would rather tell you that, clear it, and charge you for the visit than sell you a part the machine did not need.
Vent runs are what make Georgetown dryer work different from one part of town to another. Sun City is single story on a slab, and the laundry room is often well inside the floor plan, so the duct goes up into the attic and travels before it gets outside. Long attic runs sag, collect lint at the low points, and in summer the duct sits in attic heat that is well above anything the dryer was designed to exhaust into. That is why the same model dries fine in one house and badly two streets over. We work Sun City, Berry Creek, Serenada, Cimarron Hills and the Del Webb side on that basis.
On the Wolf Ranch and Water Oak side, more of the laundry rooms are upstairs, which brings a different set of problems: a vertical run with a long horizontal leg, a roof termination that nobody has looked at since the house was built, and stacked pairs that have to come apart to be serviced. In the older blocks around the Square and along San Gabriel we still find dryers vented into crawl spaces or into the attic itself, which is both a moisture problem and a fire problem, and we will tell you about it whether or not it is what you called us for. Georgetown is a short run from Leander and a same day slot is usually open.
Once a year for a normal household, and sooner if the run is long or has several elbows. The signal to watch is cycle time: if a load that used to take forty minutes now takes seventy, the vent is telling you before the dryer does.
We do it as part of the dryer work, because on a dryer call the vent is usually part of the diagnosis. If the run is crushed, sagging or wrongly terminated, we will tell you what it would take to put it right rather than clearing it and leaving the cause in place.
No. We work on gas and electric. Gas dryers have a different failure chain — igniter, valve coils and flame sensor instead of an element — and they are generally cheaper to put right when the heat goes. What we will not do is leave a gas connection we are not satisfied with.
Yes, but only alongside finding out why it blew. A thermal fuse is a one time safety device that opens because the machine overheated, and overheating nearly always means restricted airflow. Replace the fuse alone and you will be buying another one.
Usually same day or next day. Call (737) 388-3867 and we will tell you straight what the day looks like rather than booking a window we cannot hold.
Tell us the brand, whether it is gas or electric, and what it is doing — no heat, damp clothes, shutting off early, noise or a smell. That is usually enough for us to bring the likely parts on the first visit. Call (737) 388-3867 or book online and we will confirm a time for Georgetown.
We repair all major residential appliance brands across Central Texas, including Whirlpool, GE, Samsung, LG, Maytag, Frigidaire, KitchenAid, Amana, Bosch, Electrolux, Hotpoint, Kenmore, Haier, Fisher & Paykel, Sub-Zero, Wolf, Viking, Thermador, JennAir, Dacor, U-Line, Marvel, Miele, and GE Monogram.